How to Clean Skateboard Bearings Using Tri-Flow

Most skate shops will generally clean your skateboard bearings for you if you ask them, but why not just learn how to do it yourself and save a little bit of time or read on thesportbro about bearings?

The method I am about to show your for cleaning your skateboard bearings is probably the most cost effective one out there.

Some people talk about using WD40 to clean their skateboard bearings, but this is probably the worst thing you can do for your bearings! Not only does WD40 leave behind remains but it is known to attract dirty and crud to your bearings. I can testify that using WD40 on my bearings killed them within a month.

What You Need

Mosey on over to your local hardware store and ask them if they have any Tri-Flow – chances are high that they will have some in stock. Buy the spray-on superior Tri-Flow lube that has the long nozzle on it so you can get into the bearings and lube them up really well. This stuff is around five dollars or less for a can in America.

Pick up some paper towels as well in case you don’t have any lying around the house, you will need them later!

Clean the Bearings

Take out each of your eight bearings and prepare them for cleaning. If you don’t know how to take out your bearings please see my other article entitled ‘How to Change Bearings on a Skateboard’.

Take off the shields to your bearings with something small like a pair of tweezers or a razor blade. They should pop right off, but be sure not to damage the inside of your bearings when doing this.

Next, set down some paper towels and take one of your bearings in your hand. With the Tri-Flow, spray your bearing down like you would hose down a car. Get into every small crack and crevice in there and spray it down.

When you feel like you have cleaned every part of the bearing you could possibly clean, lay it down on a paper towel and let it dry out. Do the same exact thing for all of your bearings and place them back into your wheels when you are finished.

Spin your wheels and you will notice your wheel now spins for much longer than it did before. Enjoy your freshly cleaned and lubricated bearings!

How To Ollie On Your Skateboard!

The Ollie is perhaps one of the most important skateboard tricks you will ever learn. It is required for virtually any other trick you can think of, and opens up a world of possibilities. Even though the Ollie may seem difficult to learn at first, with the right method of practice, it will become second nature to you.

Learning to Ollie on Your Skateboard

The first thing to remember when trying to learn the Ollie is that skateboarding employs a great deal of physics. Balance, Weight Distribution, and movement of the feet are also very important. To perform a successful Ollie, the first thing you need to do is Pop the tail end of your board up with your foot. Practice this step by itself until it becomes natural to you.

The next step is to slide your front foot up the board. This is the most important step, and one that causes the most problems. Practice this step with the first slowly, until you’ve perfected it.

The third step is to balance out your weight in the air, and set your footing for the landing. This step is also very important, because failure to do it properly could result in some nasty falls.

It is now time to put all the steps together into one quick, fluid motion. It is natural that it feel awkward at first, but with the proper amount of practice, you’ll get the hang of it.

It is best to practice the Ollie on grass or carpet at first, to keep the board stationary. This will result in less falls until you’ve mastered it. Once you feel comfortable with it, you’re ready to take the ollie onto the cement, wood or whatever you ride on.

Side Note: Make sure the wheels and bearings are well lubricated. You can learn more about it here

The next step is to work on completing the ollie while in motion. You are likely to fall a lot at first, so go slow. As you’re going, pop the tail of your board, slide your foot up and try to balance the board out in the air and land flat so that you are less likely to be off balance.

Once you get the hang of the ollie in motion, you can attempt it off ramps and over objects. This is where it gets very dangerous, and you are strongly encouraged to wear the proper safety gear. Safety gear include a helmet, knee pads, elbow pads, proper shoes, etc. Practicing without these could result in serious injury.

Keep practicing, and doing it safely and one day you may just be the next Tony Hawk.